Can I wire my LED light bar?
Youll most likely be wiring your LED light bar relays power lead directly to the battery, but you wont necessarily use the same batterys negative terminal as your ground. You can ground your wiring to the vehicles chassis, as long as it offers a clean connection between your circuit and bare metal.
Do I need a relay to wire a LED light bar?
A relay is an electrical switch that lets a low current circuit control a high current circuit such as a large LED light bar. If you are using a light pod that does not have a very large amp draw, you may not need a relay switch, but if you are using a larger LED light bar, they are a must have.
Why does my light bar have 3 wires?
LED Lights with 3 wires will be a multi-function light. They can (most times) be used in whatever configuration is right for your application. For example, running and brake, running and blinker or brake and blinker. These LEDs will usually have a black, red and white wire.
How do you wire up LED lights?
1:185:41How to wire LED Lights & Use 2-Way switches | 12 Volt Planet - YouTubeYouTube
What size fuse should I use for my light bar?
A 10 amp fuse will protect the circuit. The 16 gauge wire will handle 10 amps in the length of wire that you will be using. The switch is rated for 20 amps. So, the 10 amp fuse will protect the circuit from overload.
What is the yellow wire for on a LED light bar?
If you want to have your light bar to turn off when the key is turned off, wire the hot into the middle yellow wire. If you like to light em up whenever and wherever you want .
What size fuse do I need for LED lights?
75mm is good for about 7.5 amps max. I generally like to have at least 100% extra rating so a 3 amp fuse max is what i would use. This should be plenty for 4 leds. If you have working leds but blow a 10A fuse i think your wiring needs checking and you will probably find your fuse is directly across the battery.
Do LED lights require special wiring?
LED lights dont need special wiring. Theyll work with any standard light fixture, as long as it isnt enclosed, which could cause heat damage. Poor wiring can cause electrical interference, but this is easily solved with a suppressor.
What happens if you wire an LED backwards?
LEDs, being diodes, will only allow current to flow in one direction. And when theres no current-flow, theres no light. Luckily, this also means that you cant break an LED by plugging it in backwards. A reversed LED can keep an entire circuit from operating properly by blocking current flow.
How do you size a 12V fuse?
Find the size of fuse by multiplying the amps required by the device (2) by 1.5. 2×1.25 = 2.5 then we will round up to the nearest fuse size (in multiples of 5 amps) which would call for a 5 amp fuse. Cross Reference that fuse size to verify that its below the Maximum fuse size called out by this chart.
What gauge wire should I use for LED lights?
18-gauge Most people would likely recommend using a solid core 18-gauge wire for your LED lights. The cost difference between this wire size and a much smaller cable is negligible, and 18-gauge is about as big as you can go if you would like your wires to fit into most holders or terminals.
Can I replace 12v halogen with LED?
Fortunately, upgrading Halogen MR16 light bulbs to LED is usually a painless affair, as most LED light bulbs are now designed to retrofit to existing light fittings. All you have to do to swap your old light bulbs out is remove them from the light fixture and fit the new, shiny light bulbs in their place.
What amp fuse do I need for LED lights?
75mm is good for about 7.5 amps max. I generally like to have at least 100% extra rating so a 3 amp fuse max is what i would use. This should be plenty for 4 leds. If you have working leds but blow a 10A fuse i think your wiring needs checking and you will probably find your fuse is directly across the battery.
How do you determine what size fuse you need?
The simple calculation is watts divided by volts equals amps. After you have calculated this, it is a simple case of adding around 10% to the value and choosing the nearest fuse to match. This is a more precise method then just guessing should you require a 3, 5, or even 13 amp fuse.
Can you put LED lights into halogen fittings?
Can I replace my incandescent or halogen bulbs with LED bulbs? Yes, in many cases, you can simply replace your bulbs separately, one by one. Furthermore, LEDs can handle all hues of white light, so the warm yellowish light of halogen bulbs is perfectly within reach!